/home/pipi/.local/lib/python3.10/site-packages/paramiko/pkey.py:100: CryptographyDeprecationWarning: TripleDES has been moved to cryptography.hazmat.decrepit.ciphers.algorithms.TripleDES and will be removed from cryptography.hazmat.primitives.ciphers.algorithms in 48.0.0.
  "cipher": algorithms.TripleDES,
/home/pipi/.local/lib/python3.10/site-packages/paramiko/transport.py:259: CryptographyDeprecationWarning: TripleDES has been moved to cryptography.hazmat.decrepit.ciphers.algorithms.TripleDES and will be removed from cryptography.hazmat.primitives.ciphers.algorithms in 48.0.0.
  "class": algorithms.TripleDES,
[WARNING]: Could not match supplied host pattern, ignoring: unprovisioned
[WARNING]: Found variable using reserved name: hosts

PLAY [Deploy initial device configuration] *************************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [ros]
ok: [s1]
ok: [s2]
ok: [r1]
ok: [r2]

TASK [Find device readiness script] ********************************************
ok: [ros]
ok: [s1]
ok: [s2]
ok: [r1]
ok: [r2]

TASK [Wait for device to become ready] *****************************************
skipping: [s1]
skipping: [s2]
skipping: [r1]
skipping: [r2]
included: /home/pipi/netlab_gh/netsim/ansible/tasks/readiness-check/srsim.yml for ros

TASK [Common SR-OS checks] *****************************************************
included: /home/pipi/netlab_gh/netsim/ansible/tasks/readiness-check/sros.yml for ros

TASK [Check that required plugin exists, use 'netlab install grpc' to install it] ***
ok: [ros]

TASK [Wait up to 180s for gNMI(TCP 57400) to be ready on clab-ml_17-ros] *******
ok: [ros -> localhost]

TASK [Update SR-SIM hardware configuration] ************************************
changed: [ros]

TASK [Get port 1/1/c1 status] **************************************************
FAILED - RETRYING: [ros]: Get port 1/1/c1 status (10 retries left).
FAILED - RETRYING: [ros]: Get port 1/1/c1 status (9 retries left).
ok: [ros]

TASK [Normalize config on bridge-like devices] *********************************
included: /home/pipi/netlab_gh/netsim/ansible/tasks/deploy-module.yml for ros, s1, s2, r1, r2

TASK [Figure out whether to deploy the module normalize on current device] *****
ok: [ros]
ok: [s1]
ok: [s2]
ok: [r1]
ok: [r2]

TASK [Find configuration template for normalize] *******************************
ok: [ros]
ok: [s1]
ok: [s2]
ok: [r1]
ok: [r2]

TASK [fail] ********************************************************************
skipping: [ros]
skipping: [s1]
skipping: [s2]
skipping: [r1]
skipping: [r2]

TASK [Find configuration deployment deploy_script for normalize] ***************
ok: [ros]
ok: [s1]
ok: [s2]
ok: [r1]
ok: [r2]

TASK [Print deployed configuration when running in verbose mode] ***************
skipping: [ros]
skipping: [s1]
skipping: [s2]
skipping: [r1]
skipping: [r2]

TASK [Deploy normalize configuration] ******************************************
skipping: [ros]
skipping: [s1]
skipping: [s2]
skipping: [r1]
skipping: [r2]

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/netlab_gh/netsim/ansible/tasks/deploy-module.yml for ros, s1, s2, r1, r2

TASK [Figure out whether to deploy the module initial on current device] *******
ok: [ros]
ok: [s1]
ok: [s2]
ok: [r1]
ok: [r2]

TASK [Find configuration template for initial] *********************************
ok: [ros]
ok: [s1]
ok: [s2]
ok: [r2]
ok: [r1]

TASK [fail] ********************************************************************
skipping: [ros]
skipping: [s1]
skipping: [s2]
skipping: [r1]
skipping: [r2]

TASK [Find configuration deployment deploy_script for initial] *****************
ok: [ros]
ok: [s1]
ok: [s2]
ok: [r2]
ok: [r1]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [ros] => 
  msg: |-
    initial configuration for ros
    =========================================
  
  
  
  
  
    updates:
    - path: configure/card[slot-number=1]
      val:
        card-type: iom-1
        mda:
        - mda-slot: 1
          mda-type: me12-100gb-qsfp28
        - mda-slot: 2
          mda-type: me12-100gb-qsfp28
        slot-number: 1
  
    - path: configure/router[router-name=Base]
      val:
       ecmp: 64
  
  
  
  
  
  
    - path: configure/router[router-name=Base]/interface[interface-name=system]
  
      val:
       admin-state: enable
       description: "System interface"
       ipv4:
        primary:
         address: "10.0.0.1"
         prefix-length: 32
ok: [s2] => 
  msg: |-
    initial configuration for s2
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # This is an artifact of unknown provenance that should be removed in a year or two (= 2026/2027)
    #
    # FRR controls these parameters with 'ip forwarding' and 'ipv6 forwarding' commands
    #
    sysctl -w net.ipv4.ip_forward=1
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    # Set system defaults
    #
    # Send ARP requests from a sane source IP address
    #
    sysctl -w net.ipv4.conf.all.arp_announce=2
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    ip link set eth1 down
    sysctl -qw net.ipv6.conf.eth1.disable_ipv6=1
    ip link set dev eth1 mtu 1500
    ip link set eth1 up
    ip link set eth2 down
    sysctl -qw net.ipv6.conf.eth2.disable_ipv6=1
    ip link set dev eth2 mtu 1500
    ip link set eth2 up
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname s2
    !
    log file /tmp/logging
  
    !
    ip forwarding
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ip address 10.0.0.3/32
    !
    interface eth1
     no shutdown
     description s2 -> s1
     ! no ip address
    !
    interface eth2
     no shutdown
     description s2 -> ros
     ! no ip address
    !
    interface eth1.701
     no shutdown
     description [SubIf VLAN blue] s2 -> s1
     ! no ip address
    !
    interface eth1.700
     no shutdown
     description [SubIf VLAN red] s2 -> s1
     ! no ip address
    !
    interface eth2.701
     no shutdown
     description [SubIf VLAN blue] s2 -> ros
     ! no ip address
    !
    interface vlan700
     no shutdown
     description VLAN red (700) -> [r1,s1,ros]
     ip address 172.16.0.3/24
    !
    interface vlan701
     no shutdown
     description VLAN blue (701) -> [ros,r2,s1]
     ip address 172.16.1.3/24
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    !
    exit 0
ok: [r1] => 
  msg: |-
    initial configuration for r1
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # This is an artifact of unknown provenance that should be removed in a year or two (= 2026/2027)
    #
    # FRR controls these parameters with 'ip forwarding' and 'ipv6 forwarding' commands
    #
    sysctl -w net.ipv4.ip_forward=1
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    # Set system defaults
    #
    # Send ARP requests from a sane source IP address
    #
    sysctl -w net.ipv4.conf.all.arp_announce=2
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    ip link set eth1 down
    sysctl -qw net.ipv6.conf.eth1.disable_ipv6=1
    ip link set dev eth1 mtu 1500
    ip link set eth1 up
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname r1
    !
    log file /tmp/logging
  
    !
    ip forwarding
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ip address 10.0.0.4/32
    !
    interface eth1
     no shutdown
     description r1 -> [s1,s2,ros]
     ip address 172.16.0.4/24
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    !
    exit 0
ok: [r2] => 
  msg: |-
    initial configuration for r2
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # This is an artifact of unknown provenance that should be removed in a year or two (= 2026/2027)
    #
    # FRR controls these parameters with 'ip forwarding' and 'ipv6 forwarding' commands
    #
    sysctl -w net.ipv4.ip_forward=1
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    # Set system defaults
    #
    # Send ARP requests from a sane source IP address
    #
    sysctl -w net.ipv4.conf.all.arp_announce=2
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    ip link set eth1 down
    sysctl -qw net.ipv6.conf.eth1.disable_ipv6=1
    ip link set dev eth1 mtu 1500
    ip link set eth1 up
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname r2
    !
    log file /tmp/logging
  
    !
    ip forwarding
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ip address 10.0.0.5/32
    !
    interface eth1
     no shutdown
     description r2 -> [ros,s1,s2]
     ip address 172.16.1.5/24
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    !
    exit 0
ok: [s1] => 
  msg: |-
    initial configuration for s1
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # This is an artifact of unknown provenance that should be removed in a year or two (= 2026/2027)
    #
    # FRR controls these parameters with 'ip forwarding' and 'ipv6 forwarding' commands
    #
    sysctl -w net.ipv4.ip_forward=1
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    #
    # Get the current next hop for the default route
    #
    def_nh=$(ip route list default|awk '{ print $3 }')
    #
    # Create the management VRF and add eth0 to it
    #
    if [ ! -e /sys/devices/virtual/net/mgmt ]; then
      ip link add mgmt type vrf table 42
    fi
    ip link set mgmt up
    sysctl -qw net.ipv6.conf.eth0.keep_addr_on_down=1
    ip link set eth0 master mgmt
    #
    # Reinstall the default route if we had it before
    #
    if [[ -n "$def_nh" ]]; then
      ip route add 0.0.0.0/0 vrf mgmt via $def_nh
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
  
    # Set system defaults
    #
    # Send ARP requests from a sane source IP address
    #
    sysctl -w net.ipv4.conf.all.arp_announce=2
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    ip link set eth1 down
    sysctl -qw net.ipv6.conf.eth1.disable_ipv6=1
    ip link set dev eth1 mtu 1500
    ip link set eth1 up
    ip link set eth2 down
    sysctl -qw net.ipv6.conf.eth2.disable_ipv6=1
    ip link set dev eth2 mtu 1500
    ip link set eth2 up
    ip link set eth3 down
    sysctl -qw net.ipv6.conf.eth3.disable_ipv6=1
    ip link set dev eth3 mtu 1500
    ip link set eth3 up
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname s1
    !
    log file /tmp/logging
  
    !
    ip forwarding
    vrf mgmt
     exit-vrf
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ip address 10.0.0.2/32
    !
    interface eth1
     no shutdown
     description s1 -> s2
     ! no ip address
    !
    interface eth2
     no shutdown
     description [Access VLAN red] s1 -> r1
     ! no ip address
    !
    interface eth3
     no shutdown
     description [Access VLAN blue] s1 -> r2
     ! no ip address
    !
    interface eth1.701
     no shutdown
     description [SubIf VLAN blue] s1 -> s2
     ! no ip address
    !
    interface eth1.700
     no shutdown
     description [SubIf VLAN red] s1 -> s2
     ! no ip address
    !
    interface vlan700
     no shutdown
     description VLAN red (700) -> [r1,s2,ros]
     ip address 172.16.0.2/24
    !
    interface vlan701
     no shutdown
     description VLAN blue (701) -> [ros,r2,s2]
     ip address 172.16.1.2/24
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    !
    exit 0

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/netlab_gh/netsim/ansible/tasks/deploy-config/sros.yml for ros
included: /home/pipi/netlab_gh/netsim/ansible/tasks/frr/initial-clab.yml for s1, s2, r1, r2

TASK [Generate gNMI YAML configuration] ****************************************
ok: [ros]

TASK [Update initial node configuration from gNMI template /home/pipi/netlab_gh/netsim/ansible/templates/initial/sros.j2] ***
changed: [ros]

TASK [debug] *******************************************************************
skipping: [ros]

TASK [Attempt to load VRF kernel module] ***************************************
changed: [s1 -> localhost]

TASK [Disable FRR management VRF when modprobe fails] **************************
skipping: [s1]
skipping: [s2]
skipping: [r1]
skipping: [r2]

TASK [include_tasks] ***********************************************************
included: /home/pipi/netlab_gh/netsim/ansible/tasks/frr/deploy-config.yml for s1, s2, r1, r2

TASK [template] ****************************************************************
changed: [r1]
changed: [s2]
changed: [s1]
changed: [r2]

TASK [set_fact] ****************************************************************
ok: [s1]
ok: [r1]
ok: [s2]
ok: [r2]

TASK [run /tmp/config.sh to deploy initial config from /home/pipi/netlab_gh/netsim/ansible/templates/initial/frr.j2] ***
changed: [s2]
changed: [s1]
changed: [r1]
changed: [r2]

TASK [run vtysh to import initial config from /home/pipi/netlab_gh/netsim/ansible/templates/initial/frr.j2] ***
skipping: [s1]
skipping: [s2]
skipping: [r1]
skipping: [r2]

PLAY [Deploy module-specific configurations] ***********************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [ros]
ok: [s1]
ok: [s2]
ok: [r1]
ok: [r2]

TASK [Deploy individual configuration modules] *********************************
included: /home/pipi/netlab_gh/netsim/ansible/tasks/deploy-module.yml for ros, s1, s2, r1, r2 => (item=vlan)
included: /home/pipi/netlab_gh/netsim/ansible/tasks/deploy-module.yml for ros, s1, s2, r1, r2 => (item=ospf)

TASK [Figure out whether to deploy the module vlan on current device] **********
ok: [ros]
ok: [s1]
ok: [s2]
ok: [r1]
ok: [r2]

TASK [Find configuration template for vlan] ************************************
ok: [ros]
skipping: [r1]
skipping: [r2]
ok: [s1]
ok: [s2]

TASK [fail] ********************************************************************
skipping: [ros]
skipping: [s1]
skipping: [s2]
skipping: [r1]
skipping: [r2]

TASK [Find configuration deployment deploy_script for vlan] ********************
skipping: [r1]
skipping: [r2]
ok: [ros]
ok: [s1]
ok: [s2]

TASK [Print deployed configuration when running in verbose mode] ***************
skipping: [r1]
skipping: [r2]
ok: [s1] => 
  msg: |-
    vlan configuration for s1
    =========================================
    #!/bin/bash
    #
    set -e # Exit immediately when any command fails
    #
    if [ ! -e /sys/devices/virtual/net/eth1.701 ]; then
      ip link add link eth1 name eth1.701 type vlan id 701
      ip link set dev eth1.701 up
    fi
    if [ ! -e /sys/devices/virtual/net/eth1.700 ]; then
      ip link add link eth1 name eth1.700 type vlan id 700
      ip link set dev eth1.700 up
    fi
    if [ ! -e /sys/devices/virtual/net/vlan700 ]; then
      ip link add vlan700 type bridge
      ip link set dev vlan700 address 52:dc:ca:fd:02:00
  
      ip link set dev vlan700 mtu 1500
      ip addr flush dev vlan700
      ip addr add 172.16.0.2/24 dev vlan700
    fi
    if [ ! -e /sys/devices/virtual/net/vlan701 ]; then
      ip link add vlan701 type bridge
      ip link set dev vlan701 address 52:dc:ca:fd:02:01
  
      ip link set dev vlan701 mtu 1500
      ip addr flush dev vlan701
      ip addr add 172.16.1.2/24 dev vlan701
    fi
  
    ip link set dev eth2 master vlan700
    ip link set dev eth3 master vlan701
    ip link set dev eth1.701 master vlan701
    ip link set dev eth1.700 master vlan700
  
    ip link set dev vlan700 up
    ip link set dev vlan701 up
ok: [s2] => 
  msg: |-
    vlan configuration for s2
    =========================================
    #!/bin/bash
    #
    set -e # Exit immediately when any command fails
    #
    if [ ! -e /sys/devices/virtual/net/eth1.701 ]; then
      ip link add link eth1 name eth1.701 type vlan id 701
      ip link set dev eth1.701 up
    fi
    if [ ! -e /sys/devices/virtual/net/eth1.700 ]; then
      ip link add link eth1 name eth1.700 type vlan id 700
      ip link set dev eth1.700 up
    fi
    if [ ! -e /sys/devices/virtual/net/eth2.701 ]; then
      ip link add link eth2 name eth2.701 type vlan id 701
      ip link set dev eth2.701 up
    fi
    if [ ! -e /sys/devices/virtual/net/vlan700 ]; then
      ip link add vlan700 type bridge
      ip link set dev vlan700 address 52:dc:ca:fd:03:00
  
      ip link set dev vlan700 mtu 1500
      ip addr flush dev vlan700
      ip addr add 172.16.0.3/24 dev vlan700
    fi
    if [ ! -e /sys/devices/virtual/net/vlan701 ]; then
      ip link add vlan701 type bridge
      ip link set dev vlan701 address 52:dc:ca:fd:03:01
  
      ip link set dev vlan701 mtu 1500
      ip addr flush dev vlan701
      ip addr add 172.16.1.3/24 dev vlan701
    fi
  
    ip link set dev eth2 master vlan700
    ip link set dev eth1.701 master vlan701
    ip link set dev eth1.700 master vlan700
    ip link set dev eth2.701 master vlan701
  
    ip link set dev vlan700 up
    ip link set dev vlan701 up
ok: [ros] => 
  msg: |-
    vlan configuration for ros
    =========================================
  
    updates:
  
  
    - path: configure/port[port-id=1/1/c1]
      val:
       admin-state: enable
       connector:
        breakout: "c1-100g"
    - path: configure/port[port-id=1/1/c1/1]
      val:
       admin-state: enable
       ethernet:
        mtu: 1518 # max 9800
        mode: network
        encap-type: dot1q
  
  
  
    - path: configure/router[router-name=Base]/interface[interface-name=eth-1/1/c1]
  
      val:
       admin-state: enable
       description: "ros ~ [r1,s1,s2] ()"
       ip-mtu: 1500
       port: "1/1/c1/1:0"
       ipv4:
        primary:
         address: "172.16.0.1"
         prefix-length: 24
  
  
  
  
  
  
    - path: configure/port[port-id=1/1/c1]
      val:
       admin-state: enable
       connector:
        breakout: "c1-100g"
    - path: configure/port[port-id=1/1/c1/1]
      val:
       admin-state: enable
       ethernet:
        encap-type: dot1q
  
  
  
    - path: configure/router[router-name=Base]/interface[interface-name=eth-1/1/c1/1_701]
  
      val:
       admin-state: enable
       description: "ros ~ [r2,s1,s2] ()vlan= 701"
       port: "1/1/c1/1:701"
       ipv4:
        primary:
         address: "172.16.1.1"
         prefix-length: 24

TASK [Deploy vlan configuration] ***********************************************
skipping: [r1]
skipping: [r2]
included: /home/pipi/netlab_gh/netsim/ansible/tasks/deploy-config/sros.yml for ros
included: /home/pipi/netlab_gh/netsim/ansible/tasks/deploy-config/frr.yml for s1, s2

TASK [Generate gNMI YAML configuration] ****************************************
ok: [ros]

TASK [Update vlan node configuration from gNMI template /home/pipi/netlab_gh/netsim/ansible/templates/vlan/sros.j2] ***
changed: [ros]

TASK [debug] *******************************************************************
skipping: [ros]

TASK [template] ****************************************************************
changed: [s2]
changed: [s1]

TASK [set_fact] ****************************************************************
ok: [s1]
ok: [s2]

TASK [run /tmp/config.sh to deploy vlan config from /home/pipi/netlab_gh/netsim/ansible/templates/vlan/frr.j2] ***
changed: [s2]
changed: [s1]

TASK [run vtysh to import vlan config from /home/pipi/netlab_gh/netsim/ansible/templates/vlan/frr.j2] ***
skipping: [s1]
skipping: [s2]

TASK [Figure out whether to deploy the module ospf on current device] **********
ok: [ros]
ok: [s1]
ok: [s2]
ok: [r1]
ok: [r2]

TASK [Find configuration template for ospf] ************************************
skipping: [s1]
skipping: [s2]
ok: [ros]
ok: [r1]
ok: [r2]

TASK [fail] ********************************************************************
skipping: [ros]
skipping: [s1]
skipping: [s2]
skipping: [r1]
skipping: [r2]

TASK [Find configuration deployment deploy_script for ospf] ********************
skipping: [s1]
skipping: [s2]
ok: [ros]
ok: [r1]
ok: [r2]

TASK [Print deployed configuration when running in verbose mode] ***************
skipping: [s1]
skipping: [s2]
ok: [r1] => 
  msg: |-
    ospf configuration for r1
    =========================================
    !
    ! OSPFv2 FRR configuration
    !
    router ospf
     ospf router-id 10.0.0.4
     timers throttle spf 10 50 500
     timers throttle lsa all 100
     timers lsa min-arrival 100
  
  
    exit
    !
    interface lo
    !
     ip ospf area 0.0.0.0
    !
    interface eth1
    ! r1 -> [s1,s2,ros]
     ip ospf area 0.0.0.0
    !
  
    !
    do write
ok: [r2] => 
  msg: |-
    ospf configuration for r2
    =========================================
    !
    ! OSPFv2 FRR configuration
    !
    router ospf
     ospf router-id 10.0.0.5
     timers throttle spf 10 50 500
     timers throttle lsa all 100
     timers lsa min-arrival 100
  
  
    exit
    !
    interface lo
    !
     ip ospf area 0.0.0.0
    !
    interface eth1
    ! r2 -> [ros,s1,s2]
     ip ospf area 0.0.0.0
    !
  
    !
    do write
ok: [ros] => 
  msg: |-
    ospf configuration for ros
    =========================================
  
  
  
  
    updates:
  
  
    - path: configure/router[router-name=Base]/ospf[ospf-instance=0]
  
      val:
        admin-state: enable
        router-id: 10.0.0.1
        area:
        - area-id: "0.0.0.0"
          interface:
          - interface-name: "system"
          - interface-name: "eth-1/1/c1"
          - interface-name: "eth-1/1/c1/1_701"

TASK [Deploy ospf configuration] ***********************************************
skipping: [s1]
skipping: [s2]
included: /home/pipi/netlab_gh/netsim/ansible/tasks/deploy-config/sros.yml for ros
included: /home/pipi/netlab_gh/netsim/ansible/tasks/deploy-config/frr.yml for r1, r2

TASK [Generate gNMI YAML configuration] ****************************************
ok: [ros]

TASK [Update ospf node configuration from gNMI template /home/pipi/netlab_gh/netsim/ansible/templates/ospf/sros.j2] ***
changed: [ros]

TASK [debug] *******************************************************************
skipping: [ros]

TASK [template] ****************************************************************
changed: [r1]
changed: [r2]

TASK [set_fact] ****************************************************************
ok: [r1]
ok: [r2]

TASK [run /tmp/config.sh to deploy ospf config from /home/pipi/netlab_gh/netsim/ansible/templates/ospf/frr.j2] ***
skipping: [r1]
skipping: [r2]

TASK [run vtysh to import ospf config from /home/pipi/netlab_gh/netsim/ansible/templates/ospf/frr.j2] ***
changed: [r2]
changed: [r1]

PLAY [Deploy custom deployment templates] **************************************
skipping: no hosts matched

PLAY RECAP *********************************************************************
r1                         : ok=28   changed=4    unreachable=0    failed=0    skipped=14   rescued=0    ignored=0   
r2                         : ok=28   changed=4    unreachable=0    failed=0    skipped=14   rescued=0    ignored=0   
ros                        : ok=37   changed=4    unreachable=0    failed=0    skipped=9    rescued=0    ignored=0   
s1                         : ok=29   changed=5    unreachable=0    failed=0    skipped=14   rescued=0    ignored=0   
s2                         : ok=28   changed=4    unreachable=0    failed=0    skipped=14   rescued=0    ignored=0   



A router-on-a-stick is attached to a VLAN trunk and runs OSPF on all attached
VLANs. One of the VLANs is a native VLAN between router-on-stick and switch.

* r1, r2, and ros should be able to ping each other

Please note it might take a while for the lab to work due to
STP and OSPF setup phase