[WARNING]: Could not match supplied host pattern, ignoring: unprovisioned

PLAY [Deploy initial device configuration] *************************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [h1]
ok: [h3]
ok: [h2]
ok: [h4]
ok: [s1]
ok: [s2]

TASK [Find device readiness script] ********************************************
ok: [h1]
ok: [h2]
ok: [h3]
ok: [h4]
ok: [s1]
ok: [s2]

TASK [Wait for device to become ready] *****************************************
skipping: [h1]
skipping: [h2]
skipping: [h3]
skipping: [h4]
included: /home/pipi/net101/tools/netsim/ansible/tasks/readiness-check/eos-clab.yml for s1, s2

TASK [Wait for cEOS SSH daemon to start] ***************************************
ok: [s2]
ok: [s1]

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for s1, s2, h1, h2, h3, h4

TASK [Figure out whether to deploy the module initial on current device] *******
ok: [h2]
ok: [h1]
ok: [h4]
ok: [h3]
ok: [s1]
ok: [s2]

TASK [Find configuration template for initial] *********************************
ok: [h1]
ok: [h2]
ok: [h3]
ok: [h4]
ok: [s1]
ok: [s2]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [h1] => 
  msg: |-
    initial configuration for h1
    =========================================
    #!/bin/bash
    #
    # This script contains the 'ip' commands needed to set up container
    # interfaces and route table. It's executed within the container
    # network namespace on the container host.
    #
    #  /etc/hosts file is generated as a clab bind.
    #
    set -e
    ### One-Shot configuration (non-Ubuntu VM or container)
    #
    # Disable IPv4 and IPv6 forwarding
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    # Interface addressing
    #
    ip link set dev eth1 up
    set +e
    ip addr del 172.16.0.1/24 dev eth1 2>/dev/null
    set -e
    ip addr add 172.16.0.1/24 dev eth1
    ip link set eth1 mtu 1500
    #
    # Add routes to IPv4 address pools pointing to the first neighbor on the first link
    #
    # If you need anything better, use FRR instead of Linux and start routing (or use IPv6)
    #
    # lan prefix: 172.16.0.0/16 local subnet: 172.16.0.0/24
    set +e
    ip route del 172.16.0.0/16 2>/dev/null
    set -e
    ip route add 172.16.0.0/16 via 172.16.0.5
    # loopback prefix: 10.0.0.0/24 local subnet: 172.16.0.0/24
    set +e
    ip route del 10.0.0.0/24 2>/dev/null
    set -e
    ip route add 10.0.0.0/24 via 172.16.0.5
    # mgmt prefix: 192.168.17.0/24 local subnet: 172.16.0.0/24
    # p2p prefix: 10.1.0.0/16 local subnet: 172.16.0.0/24
    set +e
    ip route del 10.1.0.0/16 2>/dev/null
    set -e
    ip route add 10.1.0.0/16 via 172.16.0.5
    # router_id prefix: 10.0.0.0/24 local subnet: 172.16.0.0/24
    # vrf_loopback prefix: 10.2.0.0/24 local subnet: 172.16.0.0/24
    set +e
    ip route del 10.2.0.0/24 2>/dev/null
    set -e
    ip route add 10.2.0.0/24 via 172.16.0.5
    #
    # Print the final routing table
    ip route
ok: [h4] => 
  msg: |-
    initial configuration for h4
    =========================================
    #!/bin/bash
    #
    # This script contains the 'ip' commands needed to set up container
    # interfaces and route table. It's executed within the container
    # network namespace on the container host.
    #
    #  /etc/hosts file is generated as a clab bind.
    #
    set -e
    ### One-Shot configuration (non-Ubuntu VM or container)
    #
    # Disable IPv4 and IPv6 forwarding
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    # Interface addressing
    #
    ip link set dev eth1 up
    set +e
    ip addr del 172.16.1.4/24 dev eth1 2>/dev/null
    set -e
    ip addr add 172.16.1.4/24 dev eth1
    ip link set eth1 mtu 1500
    #
    # Add routes to IPv4 address pools pointing to the first neighbor on the first link
    #
    # If you need anything better, use FRR instead of Linux and start routing (or use IPv6)
    #
    # lan prefix: 172.16.0.0/16 local subnet: 172.16.1.0/24
    set +e
    ip route del 172.16.0.0/16 2>/dev/null
    set -e
    ip route add 172.16.0.0/16 via 172.16.1.6
    # loopback prefix: 10.0.0.0/24 local subnet: 172.16.1.0/24
    set +e
    ip route del 10.0.0.0/24 2>/dev/null
    set -e
    ip route add 10.0.0.0/24 via 172.16.1.6
    # mgmt prefix: 192.168.17.0/24 local subnet: 172.16.1.0/24
    # p2p prefix: 10.1.0.0/16 local subnet: 172.16.1.0/24
    set +e
    ip route del 10.1.0.0/16 2>/dev/null
    set -e
    ip route add 10.1.0.0/16 via 172.16.1.6
    # router_id prefix: 10.0.0.0/24 local subnet: 172.16.1.0/24
    # vrf_loopback prefix: 10.2.0.0/24 local subnet: 172.16.1.0/24
    set +e
    ip route del 10.2.0.0/24 2>/dev/null
    set -e
    ip route add 10.2.0.0/24 via 172.16.1.6
    #
    # Print the final routing table
    ip route
ok: [s1] => 
  msg: |-
    initial configuration for s1
    =========================================
    hostname s1
    !
    logging monitor debugging
    !
    lldp run
    ip routing
    !
    !
    ip host h1 172.16.0.1
    ip host h2 172.16.0.2
    ip host h3 172.16.1.3
    ip host h4 172.16.1.4
    ip host s2 10.0.0.6 172.16.0.6 172.16.1.6
    !
    interface Management0
     no lldp transmit
     no lldp receive
    !
    interface Loopback0
     no shutdown
     ip address 10.0.0.5/32
    !
    interface Ethernet1
     no shutdown
     no switchport
    !
     mac-address 52dc.cafe.0501
    !
    interface Ethernet2
     no shutdown
     no switchport
    !
     mac-address 52dc.cafe.0502
    !
    interface Ethernet3
     no shutdown
     no switchport
    !
     mac-address 52dc.cafe.0503
    !
    interface Vlan1000
     no shutdown
     description VLAN red (1000) -> [s2,h1,h2]
     ip address 172.16.0.5/24
    !
    interface Vlan1001
     no shutdown
     description VLAN blue (1001) -> [h3,s2,h4]
     ip address 172.16.1.5/24
    !
ok: [h3] => 
  msg: |-
    initial configuration for h3
    =========================================
    #!/bin/bash
    #
    # This script contains the 'ip' commands needed to set up container
    # interfaces and route table. It's executed within the container
    # network namespace on the container host.
    #
    #  /etc/hosts file is generated as a clab bind.
    #
    set -e
    ### One-Shot configuration (non-Ubuntu VM or container)
    #
    # Disable IPv4 and IPv6 forwarding
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    # Interface addressing
    #
    ip link set dev eth1 up
    set +e
    ip addr del 172.16.1.3/24 dev eth1 2>/dev/null
    set -e
    ip addr add 172.16.1.3/24 dev eth1
    ip link set eth1 mtu 1500
    #
    # Add routes to IPv4 address pools pointing to the first neighbor on the first link
    #
    # If you need anything better, use FRR instead of Linux and start routing (or use IPv6)
    #
    # lan prefix: 172.16.0.0/16 local subnet: 172.16.1.0/24
    set +e
    ip route del 172.16.0.0/16 2>/dev/null
    set -e
    ip route add 172.16.0.0/16 via 172.16.1.5
    # loopback prefix: 10.0.0.0/24 local subnet: 172.16.1.0/24
    set +e
    ip route del 10.0.0.0/24 2>/dev/null
    set -e
    ip route add 10.0.0.0/24 via 172.16.1.5
    # mgmt prefix: 192.168.17.0/24 local subnet: 172.16.1.0/24
    # p2p prefix: 10.1.0.0/16 local subnet: 172.16.1.0/24
    set +e
    ip route del 10.1.0.0/16 2>/dev/null
    set -e
    ip route add 10.1.0.0/16 via 172.16.1.5
    # router_id prefix: 10.0.0.0/24 local subnet: 172.16.1.0/24
    # vrf_loopback prefix: 10.2.0.0/24 local subnet: 172.16.1.0/24
    set +e
    ip route del 10.2.0.0/24 2>/dev/null
    set -e
    ip route add 10.2.0.0/24 via 172.16.1.5
    #
    # Print the final routing table
    ip route
ok: [s2] => 
  msg: |-
    initial configuration for s2
    =========================================
    hostname s2
    !
    logging monitor debugging
    !
    lldp run
    ip routing
    !
    !
    ip host h1 172.16.0.1
    ip host h2 172.16.0.2
    ip host h3 172.16.1.3
    ip host h4 172.16.1.4
    ip host s1 10.0.0.5 172.16.0.5 172.16.1.5
    !
    interface Management0
     no lldp transmit
     no lldp receive
    !
    interface Loopback0
     no shutdown
     ip address 10.0.0.6/32
    !
    interface Ethernet1
     no shutdown
     no switchport
    !
     mac-address 52dc.cafe.0601
    !
    interface Ethernet2
     no shutdown
     no switchport
    !
     mac-address 52dc.cafe.0602
    !
    interface Ethernet3
     no shutdown
     no switchport
    !
     mac-address 52dc.cafe.0603
    !
    interface Vlan1000
     no shutdown
     description VLAN red (1000) -> [s1,h1,h2]
     ip address 172.16.0.6/24
    !
    interface Vlan1001
     no shutdown
     description VLAN blue (1001) -> [h3,s1,h4]
     ip address 172.16.1.6/24
    !
ok: [h2] => 
  msg: |-
    initial configuration for h2
    =========================================
    #!/bin/bash
    #
    # This script contains the 'ip' commands needed to set up container
    # interfaces and route table. It's executed within the container
    # network namespace on the container host.
    #
    #  /etc/hosts file is generated as a clab bind.
    #
    set -e
    ### One-Shot configuration (non-Ubuntu VM or container)
    #
    # Disable IPv4 and IPv6 forwarding
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    # Interface addressing
    #
    ip link set dev eth1 up
    set +e
    ip addr del 172.16.0.2/24 dev eth1 2>/dev/null
    set -e
    ip addr add 172.16.0.2/24 dev eth1
    ip link set eth1 mtu 1500
    #
    # Add routes to IPv4 address pools pointing to the first neighbor on the first link
    #
    # If you need anything better, use FRR instead of Linux and start routing (or use IPv6)
    #
    # lan prefix: 172.16.0.0/16 local subnet: 172.16.0.0/24
    set +e
    ip route del 172.16.0.0/16 2>/dev/null
    set -e
    ip route add 172.16.0.0/16 via 172.16.0.6
    # loopback prefix: 10.0.0.0/24 local subnet: 172.16.0.0/24
    set +e
    ip route del 10.0.0.0/24 2>/dev/null
    set -e
    ip route add 10.0.0.0/24 via 172.16.0.6
    # mgmt prefix: 192.168.17.0/24 local subnet: 172.16.0.0/24
    # p2p prefix: 10.1.0.0/16 local subnet: 172.16.0.0/24
    set +e
    ip route del 10.1.0.0/16 2>/dev/null
    set -e
    ip route add 10.1.0.0/16 via 172.16.0.6
    # router_id prefix: 10.0.0.0/24 local subnet: 172.16.0.0/24
    # vrf_loopback prefix: 10.2.0.0/24 local subnet: 172.16.0.0/24
    set +e
    ip route del 10.2.0.0/24 2>/dev/null
    set -e
    ip route add 10.2.0.0/24 via 172.16.0.6
    #
    # Print the final routing table
    ip route

TASK [Find configuration deployment deploy_script for initial] *****************
ok: [h1]
ok: [h4]
ok: [h2]
ok: [h3]
ok: [s1]
ok: [s2]

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/eos.yml for s1, s2
included: /home/pipi/net101/tools/netsim/ansible/tasks/linux/initial-clab.yml for h1, h2, h3, h4

TASK [eos_config: deploying initial from /home/pipi/net101/tools/netsim/ansible/templates/initial/eos.j2] ***
[WARNING]: To ensure idempotency and correct diff the input configuration lines
should be similar to how they appear if present in the running configuration on
device including the indentation
changed: [s2]
changed: [s1]

TASK [set_fact] ****************************************************************
ok: [h1]
ok: [h2]
ok: [h3]
ok: [h4]

TASK [Create initial container setup from /home/pipi/net101/tools/netsim/ansible/templates/initial/linux-clab.j2] ***
changed: [h4 -> localhost]
changed: [h1 -> localhost]
changed: [h3 -> localhost]
changed: [h2 -> localhost]

TASK [Initial container configuration via /tmp/config-NhxWLmLP-h1.sh] **********
changed: [h1 -> localhost]
changed: [h3 -> localhost]
changed: [h2 -> localhost]
changed: [h4 -> localhost]

TASK [file] ********************************************************************
changed: [h2 -> localhost]
changed: [h4 -> localhost]
changed: [h1 -> localhost]
changed: [h3 -> localhost]

PLAY [Deploy module-specific configurations] ***********************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [s1]
ok: [s2]

TASK [Deploy individual configuration modules] *********************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for s1, s2 => (item=vlan)

TASK [Figure out whether to deploy the module vlan on current device] **********
ok: [s1]
ok: [s2]

TASK [Find configuration template for vlan] ************************************
ok: [s1]
ok: [s2]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [s2] => 
  msg: |-
    vlan configuration for s2
    =========================================
    vlan 1001
     name blue
    !
    vlan 1000
     name red
    !
  
    !
    interface Ethernet1
     switchport
     switchport mode trunk
     switchport trunk allowed vlan 1000,1001
     switchport trunk native vlan 1000
    !
    interface Ethernet2
     switchport
     switchport access vlan 1000
    !
    interface Ethernet3
     switchport
     switchport access vlan 1001
    !
    interface Vlan1000
    !
    interface Vlan1001
ok: [s1] => 
  msg: |-
    vlan configuration for s1
    =========================================
    vlan 1001
     name blue
    !
    vlan 1000
     name red
    !
  
    !
    interface Ethernet1
     switchport
     switchport mode trunk
     switchport trunk allowed vlan 1000,1001
     switchport trunk native vlan 1000
    !
    interface Ethernet2
     switchport
     switchport access vlan 1000
    !
    interface Ethernet3
     switchport
     switchport access vlan 1001
    !
    interface Vlan1000
    !
    interface Vlan1001

TASK [Find configuration deployment deploy_script for vlan] ********************
ok: [s2]
ok: [s1]

TASK [Deploy vlan configuration] ***********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/eos.yml for s1, s2

TASK [eos_config: deploying vlan from /home/pipi/net101/tools/netsim/ansible/templates/vlan/eos.j2] ***
changed: [s2]
changed: [s1]

PLAY [Deploy custom deployment templates] **************************************
skipping: no hosts matched

PLAY RECAP *********************************************************************
h1                         : ok=12   changed=3    unreachable=0    failed=0    skipped=1    rescued=0    ignored=0   
h2                         : ok=12   changed=3    unreachable=0    failed=0    skipped=1    rescued=0    ignored=0   
h3                         : ok=12   changed=3    unreachable=0    failed=0    skipped=1    rescued=0    ignored=0   
h4                         : ok=12   changed=3    unreachable=0    failed=0    skipped=1    rescued=0    ignored=0   
s1                         : ok=19   changed=2    unreachable=0    failed=0    skipped=0    rescued=0    ignored=0   
s2                         : ok=19   changed=2    unreachable=0    failed=0    skipped=0    rescued=0    ignored=0   



The devices under test are layer-3 switches bridging
between ports in the same VLAN and routing across VLANs.
One of the VLANs is a native VLAN on the trunk link.

* All hosts should be able to ping each other and
  switch interfaces in the same VLAN
* Hosts should be able to ping loopback address of the
  adjacent switch (static routes point to nearest router)

Please note it might take a while for the lab to work due to
STP learning phase