[WARNING]: Could not match supplied host pattern, ignoring: unprovisioned

PLAY [Deploy initial device configuration] *************************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [dut]
ok: [xs]
ok: [h1]
ok: [h2]
ok: [h3]
ok: [h4]

TASK [Find device readiness script] ********************************************
ok: [dut]
ok: [xs]
ok: [h1]
ok: [h2]
ok: [h4]
ok: [h3]

TASK [Wait for device to become ready] *****************************************
skipping: [dut]
skipping: [xs]
skipping: [h1]
skipping: [h2]
skipping: [h3]
skipping: [h4]

TASK [Normalize config on bridge-like devices] *********************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, xs, h1, h2, h3, h4

TASK [Figure out whether to deploy the module normalize on current device] *****
ok: [dut]
ok: [xs]
ok: [h1]
ok: [h2]
ok: [h3]
ok: [h4]

TASK [Find configuration template for normalize] *******************************
ok: [dut]
ok: [xs]
ok: [h1]
ok: [h2]
ok: [h3]
ok: [h4]

TASK [fail] ********************************************************************
skipping: [dut]
skipping: [xs]
skipping: [h1]
skipping: [h2]
skipping: [h3]
skipping: [h4]

TASK [Print deployed configuration when running in verbose mode] ***************
skipping: [dut]
skipping: [xs]
skipping: [h1]
skipping: [h2]
skipping: [h3]
skipping: [h4]

TASK [Find configuration deployment deploy_script for normalize] ***************
skipping: [dut]
skipping: [xs]
skipping: [h1]
skipping: [h2]
skipping: [h3]
skipping: [h4]

TASK [Deploy normalize configuration] ******************************************
skipping: [dut]
skipping: [xs]
skipping: [h1]
skipping: [h2]
skipping: [h3]
skipping: [h4]

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, xs, h1, h2, h3, h4

TASK [Figure out whether to deploy the module initial on current device] *******
ok: [dut]
ok: [xs]
ok: [h1]
ok: [h2]
ok: [h3]
ok: [h4]

TASK [Find configuration template for initial] *********************************
ok: [dut]
ok: [xs]
ok: [h1]
ok: [h2]
ok: [h3]
ok: [h4]

TASK [fail] ********************************************************************
skipping: [dut]
skipping: [xs]
skipping: [h1]
skipping: [h2]
skipping: [h3]
skipping: [h4]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [h1] => 
  msg: |-
    initial configuration for h1
    =========================================
    #!/bin/bash
    #
    # This script contains the 'ip' commands needed to set up container
    # interfaces and route table. It's executed within the container
    # network namespace on the container host.
    #
    #  /etc/hosts file is generated as a clab bind.
    #
    set -e
  
    ### One-Shot configuration (non-Ubuntu VM or container)
    #
    # Disable IPv4 and IPv6 forwarding
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    # Interface addressing, create any bond devices
    #
    ip link set dev eth1 up
    set +e
    ip addr del 172.16.0.1/24 dev eth1 2>/dev/null
    set -e
    ip addr add 172.16.0.1/24 dev eth1
    ip link set dev eth1 mtu 1500
    #
    # Add static routes (usually IPv4 routes pointing to the first usable gateway)
    #
    echo Removing existing IPv4 routes
    while ip route del 172.16.0.0/16 2>/dev/null; do
      : ; done
    while ip route del 10.0.0.0/24 2>/dev/null; do
      : ; done
    while ip route del 10.1.0.0/16 2>/dev/null; do
      : ; done
    while ip route del 10.2.0.0/24 2>/dev/null; do
      : ; done
    #
    #
    echo Adding direct static routes
    ip route add 172.16.0.0/16 via 172.16.0.5 dev eth1 protocol static
    ip route add 10.0.0.0/24 via 172.16.0.5 dev eth1 protocol static
    ip route add 10.1.0.0/16 via 172.16.0.5 dev eth1 protocol static
    ip route add 10.2.0.0/24 via 172.16.0.5 dev eth1 protocol static
    #
    # Print the final routing table
    ip route
ok: [dut] => 
  msg: |-
    initial configuration for dut
    =========================================
  
    - set:
        system:
          hostname: dut
          config:
            snippet:
              system-mtu:
                file: /etc/network/ifupdown2/policy.d/mtu.json
                content: |
                  { "address": { "defaults": { "mtu": "1500" } } }
        interface:
          eth0:
            ip:
              vrf: mgmt
              address:
                dhcp: {}
            type: eth
          bond1:
            type: bond
            link:
              state:
                up : {}
            description: "dut -> xs"
            ip:
              ipv6:
                enable: off
            bridge:
              domain:
                br_default: {}
  
          swp1:
            type: swp
            link:
              state:
                down : {}
            description: "dut -> xs"
            ip:
              ipv6:
                enable: off
  
          swp2:
            type: swp
            link:
              state:
                down : {}
            description: "dut -> xs"
            ip:
              ipv6:
                enable: off
  
          swp3:
            type: swp
            link:
              state:
                up : {}
            description: "[Access VLAN v1] dut -> h1"
            ip:
              ipv6:
                enable: off
  
          swp4:
            type: swp
            link:
              state:
                up : {}
            description: "[Access VLAN v2] dut -> h3"
            ip:
              ipv6:
                enable: off
  
          vlan1000:
            type: svi
            link:
              state:
                up : {}
            description: "VLAN v1 (1000) -> [h1,xs,h2]"
            ip:
              address:
                172.16.0.5/24: {}
              ipv6:
                enable: off
  
          vlan1001:
            type: svi
            link:
              state:
                up : {}
            description: "VLAN v2 (1001) -> [h3,xs,h4]"
            ip:
              address:
                172.16.1.5/24: {}
              ipv6:
                enable: off
  
  
    - set:
        interface:
          lo:
            type: loopback
            ip:
              address:
                10.0.0.5/32: {}
              ipv6:
                enable: off
ok: [h4] => 
  msg: |-
    initial configuration for h4
    =========================================
    #!/bin/bash
    #
    # This script contains the 'ip' commands needed to set up container
    # interfaces and route table. It's executed within the container
    # network namespace on the container host.
    #
    #  /etc/hosts file is generated as a clab bind.
    #
    set -e
  
    ### One-Shot configuration (non-Ubuntu VM or container)
    #
    # Disable IPv4 and IPv6 forwarding
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    # Interface addressing, create any bond devices
    #
    ip link set dev eth1 up
    set +e
    ip addr del 172.16.1.4/24 dev eth1 2>/dev/null
    set -e
    ip addr add 172.16.1.4/24 dev eth1
    ip link set dev eth1 mtu 1500
    #
    # Add static routes (usually IPv4 routes pointing to the first usable gateway)
    #
    echo Removing existing IPv4 routes
    while ip route del 172.16.0.0/16 2>/dev/null; do
      : ; done
    while ip route del 10.0.0.0/24 2>/dev/null; do
      : ; done
    while ip route del 10.1.0.0/16 2>/dev/null; do
      : ; done
    while ip route del 10.2.0.0/24 2>/dev/null; do
      : ; done
    #
    #
    echo Adding direct static routes
    ip route add 172.16.0.0/16 via 172.16.1.6 dev eth1 protocol static
    ip route add 10.0.0.0/24 via 172.16.1.6 dev eth1 protocol static
    ip route add 10.1.0.0/16 via 172.16.1.6 dev eth1 protocol static
    ip route add 10.2.0.0/24 via 172.16.1.6 dev eth1 protocol static
    #
    # Print the final routing table
    ip route
ok: [h2] => 
  msg: |-
    initial configuration for h2
    =========================================
    #!/bin/bash
    #
    # This script contains the 'ip' commands needed to set up container
    # interfaces and route table. It's executed within the container
    # network namespace on the container host.
    #
    #  /etc/hosts file is generated as a clab bind.
    #
    set -e
  
    ### One-Shot configuration (non-Ubuntu VM or container)
    #
    # Disable IPv4 and IPv6 forwarding
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    # Interface addressing, create any bond devices
    #
    ip link set dev eth1 up
    set +e
    ip addr del 172.16.0.2/24 dev eth1 2>/dev/null
    set -e
    ip addr add 172.16.0.2/24 dev eth1
    ip link set dev eth1 mtu 1500
    #
    # Add static routes (usually IPv4 routes pointing to the first usable gateway)
    #
    echo Removing existing IPv4 routes
    while ip route del 172.16.0.0/16 2>/dev/null; do
      : ; done
    while ip route del 10.0.0.0/24 2>/dev/null; do
      : ; done
    while ip route del 10.1.0.0/16 2>/dev/null; do
      : ; done
    while ip route del 10.2.0.0/24 2>/dev/null; do
      : ; done
    #
    #
    echo Adding direct static routes
    ip route add 172.16.0.0/16 via 172.16.0.6 dev eth1 protocol static
    ip route add 10.0.0.0/24 via 172.16.0.6 dev eth1 protocol static
    ip route add 10.1.0.0/16 via 172.16.0.6 dev eth1 protocol static
    ip route add 10.2.0.0/24 via 172.16.0.6 dev eth1 protocol static
    #
    # Print the final routing table
    ip route
ok: [h3] => 
  msg: |-
    initial configuration for h3
    =========================================
    #!/bin/bash
    #
    # This script contains the 'ip' commands needed to set up container
    # interfaces and route table. It's executed within the container
    # network namespace on the container host.
    #
    #  /etc/hosts file is generated as a clab bind.
    #
    set -e
  
    ### One-Shot configuration (non-Ubuntu VM or container)
    #
    # Disable IPv4 and IPv6 forwarding
    #
    sysctl -w net.ipv4.ip_forward=0
    sysctl -w net.ipv6.conf.all.forwarding=0
    #
    # Interface addressing, create any bond devices
    #
    ip link set dev eth1 up
    set +e
    ip addr del 172.16.1.3/24 dev eth1 2>/dev/null
    set -e
    ip addr add 172.16.1.3/24 dev eth1
    ip link set dev eth1 mtu 1500
    #
    # Add static routes (usually IPv4 routes pointing to the first usable gateway)
    #
    echo Removing existing IPv4 routes
    while ip route del 172.16.0.0/16 2>/dev/null; do
      : ; done
    while ip route del 10.0.0.0/24 2>/dev/null; do
      : ; done
    while ip route del 10.1.0.0/16 2>/dev/null; do
      : ; done
    while ip route del 10.2.0.0/24 2>/dev/null; do
      : ; done
    #
    #
    echo Adding direct static routes
    ip route add 172.16.0.0/16 via 172.16.1.5 dev eth1 protocol static
    ip route add 10.0.0.0/24 via 172.16.1.5 dev eth1 protocol static
    ip route add 10.1.0.0/16 via 172.16.1.5 dev eth1 protocol static
    ip route add 10.2.0.0/24 via 172.16.1.5 dev eth1 protocol static
    #
    # Print the final routing table
    ip route
ok: [xs] => 
  msg: |-
    initial configuration for xs
    =========================================
    #!/bin/bash
    #
    set -e
    set -x
    #
    # Create bash profile script
    #
    cat <<SCRIPT >/root/.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)# "
    echo
    echo "Use vtysh to connect to FRR daemon"
    echo
    SCRIPT
    cat <<SCRIPT >.bash_profile
    #!/bin/bash
    #
    export PS1="\h(bash)$ "
    export PATH=$PATH:/usr/sbin
    echo
    echo "Use sudo vtysh to connect to FRR daemon"
    echo
    SCRIPT
    #
    # Build hosts file
    #
    #
    cat <<SCRIPT >/tmp/hosts
    #
    # Created by netlab initial
    #
    10.0.0.5 dut
    172.16.0.5 vlan1000.dut
    172.16.1.5 vlan1001.dut
    10.0.0.6 xs
    172.16.0.6 vlan1000.xs
    172.16.1.6 vlan1001.xs
    172.16.0.1 h1 eth1.h1
    172.16.0.2 h2 eth1.h2
    172.16.1.3 h3 eth1.h3
    172.16.1.4 h4 eth1.h4
    SCRIPT
    grep "Created by netlab" /etc/hosts || uniq /tmp/hosts >>/etc/hosts
    #
    # Configure system defaults on Ubuntu
    #
    hostnamectl set-hostname xs
    sysctl -w net.ipv4.ip_forward=1
    sysctl -w net.ipv6.conf.all.forwarding=1
    APT_INSTALL=
    #
    if which curl; then
      echo "Package curl already installed"
    else
      APT_INSTALL="$APT_INSTALL curl"
    fi
    #
    if which gpg; then
      echo "Package gnupg already installed"
    else
      APT_INSTALL="$APT_INSTALL gnupg"
    fi
    #
    if which bridge; then
      echo "Package iproute2 already installed"
    else
      APT_INSTALL="$APT_INSTALL iproute2"
    fi
    #
    # APT_INSTALL always starts with a blank, so we can't just check if it's empty
    # The following hack turns a string that contains only whitespaces into
    # an empty string and removes leading whitespaces
    #
    APT_INSTALL=`echo $APT_INSTALL`
    if [ -n "$APT_INSTALL" ]; then
      echo "Installing packages $APT_INSTALL"
      apt-get update -qq && apt-get install -qq $APT_INSTALL
    fi
    #
    # Install FRR on a Ubuntu VM if needed
    #
    if which /usr/lib/frr/frrinit.sh; then
      echo "FRR already installed, skipping installation"
    else
      curl -s https://deb.frrouting.org/frr/keys.asc >/etc/apt/trusted.gpg.d/frr.asc
      FRRVER="frr-stable"
      echo deb https://deb.frrouting.org/frr $(lsb_release -s -c) $FRRVER > /etc/apt/sources.list.d/frr.list
      apt-get update -qq && apt-get install -qq frr frr-pythontools bridge-utils ethtool
    fi
    #
    # Enable FRR modules (if not using containerlab bind-mounted /etc/frr/daemons)
    #
    #
    # Enable FRR daemons
    #
  
    /usr/lib/frr/frrinit.sh restart
  
    #
    # Create loopbacks, stub and lag/bond devices
    #
    if [ ! -e /sys/class/net/lo ]; then
      if [ ! -e /sys/devices/virtual/net/lo ]; then
        ip link add lo type dummy
        ip link set dev lo up
      fi
    fi
    if [ ! -e /sys/class/net/bond1 ]; then
      if [ ! -e /sys/devices/virtual/net/bond1 ]; then
    #
    # Make sure 'bonding' module is loaded
    #
    if [ ! -e /sys/module/bonding ]; then
    modprobe bonding miimon=100 mode=802.3ad lacp_rate=fast
    fi
    if [ ! -e /sys/class/net/bond1 ]; then
    ip link add dev bond1 type bond mode 802.3ad lacp_rate slow
    fi
  
        ip link set dev bond1 up
      fi
    fi
  
    # Disable IPv6 (for IPv4-only interfaces) or SLAAC (if the device is a router)
    #
    sysctl -qw net.ipv6.conf.bond1.disable_ipv6=1
    ip link set dev bond1 mtu 1500
    sysctl -qw net.ipv6.conf.eth1.disable_ipv6=1
    ip link set dev eth1 mtu 1500
    sysctl -qw net.ipv6.conf.eth2.disable_ipv6=1
    ip link set dev eth2 mtu 1500
    sysctl -qw net.ipv6.conf.eth3.disable_ipv6=1
    ip link set dev eth3 mtu 1500
    sysctl -qw net.ipv6.conf.eth4.disable_ipv6=1
    ip link set dev eth4 mtu 1500
  
    #
    # Add vtysh.conf file
    echo "service integrated-vtysh-config" >/etc/frr/vtysh.conf
  
    #
    # Rest of initial configuration done through VTYSH
    #
    cat >/tmp/config <<CONFIG
    hostname xs
    !
    frr defaults datacenter
    !
    interface lo
     no shutdown
     ip address 10.0.0.6/32
    !
    interface bond1
     no shutdown
     description xs -> dut
     ! no ip address
    !
    interface eth1
     no shutdown
     description xs -> dut
     ! no ip address
    !
    interface eth2
     no shutdown
     description xs -> dut
     ! no ip address
    !
    interface eth3
     no shutdown
     description [Access VLAN v1] xs -> h2
     ! no ip address
    !
    interface eth4
     no shutdown
     description [Access VLAN v2] xs -> h4
     ! no ip address
    !
    interface bond1.1000
     no shutdown
     description [SubIf VLAN v1] xs -> dut
     ! no ip address
    !
    interface bond1.1001
     no shutdown
     description [SubIf VLAN v2] xs -> dut
     ! no ip address
    !
    interface vlan1000
     no shutdown
     description VLAN v1 (1000) -> [h1,dut,h2]
     ip address 172.16.0.6/24
    !
    interface vlan1001
     no shutdown
     description VLAN v2 (1001) -> [h3,dut,h4]
     ip address 172.16.1.6/24
    !
    do write
    CONFIG
    vtysh -f /tmp/config
    exit 0

TASK [Find configuration deployment deploy_script for initial] *****************
ok: [dut]
ok: [xs]
ok: [h1]
ok: [h3]
ok: [h2]
ok: [h4]

TASK [Deploy initial configuration] ********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/cumulus_nvue.yml for dut
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/frr.yml for xs
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/linux-clab.yml for h1, h2, h3, h4

TASK [set_fact] ****************************************************************
ok: [dut]

TASK [copy the cumulus nvue YAML initial config file to switch (generated from /home/pipi/net101/tools/netsim/ansible/templates/initial/cumulus_nvue.j2)] ***
changed: [dut]

TASK [Wait for nvued to start] *************************************************
ok: [dut]

TASK [set_fact] ****************************************************************
ok: [dut]

TASK [execute on cumulus: 'nv config patch' for initial config] ****************
changed: [dut]

TASK [execute on cumulus: 'nv config apply -y' for initial config] *************
changed: [dut]

TASK [template] ****************************************************************
changed: [xs]

TASK [set_fact] ****************************************************************
ok: [xs]

TASK [run /tmp/config.sh to deploy initial config from /home/pipi/net101/tools/netsim/ansible/templates/initial/frr.j2] ***
changed: [xs]

TASK [run vtysh to import initial config from /home/pipi/net101/tools/netsim/ansible/templates/initial/frr.j2] ***
skipping: [xs]

TASK [Define script filename and determine whether to execute in netns] ********
ok: [h1]
ok: [h2]
ok: [h3]
ok: [h4]

TASK [Create a temporary file for the rendered script] *************************
changed: [h2 -> localhost]
changed: [h3 -> localhost]
changed: [h1 -> localhost]
changed: [h4 -> localhost]

TASK [Create container setup script from /home/pipi/net101/tools/netsim/ansible/templates/initial/linux-clab.j2] ***
changed: [h1 -> localhost]
changed: [h3 -> localhost]
changed: [h2 -> localhost]
changed: [h4 -> localhost]

TASK [Copy script into running container at /tmp/config-h1_initial.sh] *********
skipping: [h1]
skipping: [h2]
skipping: [h3]
skipping: [h4]

TASK [Execute /tmp/config-h1_initial.sh to deploy initial config based on /home/pipi/net101/tools/netsim/ansible/templates/initial/linux-clab.j2] ***
skipping: [h1]
skipping: [h2]
skipping: [h3]
skipping: [h4]

TASK [Container configuration for initial based on /home/pipi/net101/tools/netsim/ansible/templates/initial/linux-clab.j2 executed in netns] ***
changed: [h1 -> localhost]
changed: [h2 -> localhost]
changed: [h3 -> localhost]
changed: [h4 -> localhost]

TASK [Remove temporary file /tmp/h1_initial-f3juu6u5.sh] ***********************
changed: [h1 -> localhost]
changed: [h3 -> localhost]
changed: [h4 -> localhost]
changed: [h2 -> localhost]

PLAY [Deploy module-specific configurations] ***********************************

TASK [Set variables that cannot be set with VARS] ******************************
ok: [dut]
ok: [xs]

TASK [Deploy individual configuration modules] *********************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, xs => (item=lag)
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-module.yml for dut, xs => (item=vlan)

TASK [Figure out whether to deploy the module lag on current device] ***********
ok: [dut]
ok: [xs]

TASK [Find configuration template for lag] *************************************
ok: [dut]
ok: [xs]

TASK [fail] ********************************************************************
skipping: [dut]
skipping: [xs]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [xs] => 
  msg: |-
    lag configuration for xs
    =========================================
    #!/bin/bash
    #
    set -e # Exit immediately when any command fails
    #
    # Bond devices are created by 'initial' module - add members
    #
    ethtool -s eth1 autoneg off speed 1000 duplex full
    ip link set dev eth1 down
    ip link set dev eth1 master bond1
    ip link set dev eth1 up
    ethtool -s eth2 autoneg off speed 1000 duplex full
    ip link set dev eth2 down
    ip link set dev eth2 master bond1
    ip link set dev eth2 up
    ip link set dev bond1 up
    exit 0
ok: [dut] => 
  msg: |-
    lag configuration for dut
    =========================================
  
    - set:
        interface:
          swp1:
            link:
              state:
                up: {}
          swp2:
            link:
              state:
                up: {}
          bond1:
            bond:
              lacp-rate: slow
              member:
                swp1: {}
                swp2: {}

TASK [Find configuration deployment deploy_script for lag] *********************
ok: [dut]
ok: [xs]

TASK [Deploy lag configuration] ************************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/cumulus_nvue.yml for dut
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/frr.yml for xs

TASK [set_fact] ****************************************************************
ok: [dut]

TASK [copy the cumulus nvue YAML lag config file to switch (generated from /home/pipi/net101/tools/netsim/ansible/templates/lag/cumulus_nvue.j2)] ***
changed: [dut]

TASK [Wait for nvued to start] *************************************************
skipping: [dut]

TASK [set_fact] ****************************************************************
ok: [dut]

TASK [execute on cumulus: 'nv config patch' for lag config] ********************
changed: [dut]

TASK [execute on cumulus: 'nv config apply -y' for lag config] *****************
changed: [dut]

TASK [template] ****************************************************************
changed: [xs]

TASK [set_fact] ****************************************************************
ok: [xs]

TASK [run /tmp/config.sh to deploy lag config from /home/pipi/net101/tools/netsim/ansible/templates/lag/frr.j2] ***
changed: [xs]

TASK [run vtysh to import lag config from /home/pipi/net101/tools/netsim/ansible/templates/lag/frr.j2] ***
skipping: [xs]

TASK [Figure out whether to deploy the module vlan on current device] **********
ok: [dut]
ok: [xs]

TASK [Find configuration template for vlan] ************************************
ok: [dut]
ok: [xs]

TASK [fail] ********************************************************************
skipping: [dut]
skipping: [xs]

TASK [Print deployed configuration when running in verbose mode] ***************
ok: [dut] => 
  msg: |-
    vlan configuration for dut
    =========================================
    - set:
        bridge:
          domain:
            br_default:
              type: vlan-aware
              mac-address: "08:4f:c2:a9:00:05" # The default 'auto' setting reads the MAC from the EEPROM, which is the same for all instances
              untagged: none
              vlan:
                '1000': {}
                '1001': {}
  
  
        interface:
         bond1:
           bridge:
             domain:
               br_default:
  
                 vlan:
                   '1000': {}
                   '1001': {}
                 untagged: none
         swp3:
           bridge:
             domain:
               br_default:
                 access: 1000
         swp4:
           bridge:
             domain:
               br_default:
                 access: 1001
ok: [xs] => 
  msg: |-
    vlan configuration for xs
    =========================================
    #!/bin/bash
    #
    set -e # Exit immediately when any command fails
    #
    if [ ! -e /sys/devices/virtual/net/bond1.1000 ]; then
      ip link add link bond1 name bond1.1000 type vlan id 1000
      ip link set dev bond1.1000 up
    fi
    if [ ! -e /sys/devices/virtual/net/bond1.1001 ]; then
      ip link add link bond1 name bond1.1001 type vlan id 1001
      ip link set dev bond1.1001 up
    fi
    if [ ! -e /sys/devices/virtual/net/vlan1000 ]; then
      brctl addbr vlan1000
      ip link set dev vlan1000 address 52:dc:ca:fd:06:00
  
      ip addr flush dev vlan1000
      ip addr add 172.16.0.6/24 dev vlan1000
    fi
    if [ ! -e /sys/devices/virtual/net/vlan1001 ]; then
      brctl addbr vlan1001
      ip link set dev vlan1001 address 52:dc:ca:fd:06:01
  
      ip addr flush dev vlan1001
      ip addr add 172.16.1.6/24 dev vlan1001
    fi
  
    brctl addif vlan1000 eth3
    brctl addif vlan1001 eth4
    brctl addif vlan1000 bond1.1000
    brctl addif vlan1001 bond1.1001
  
    ip link set dev vlan1000 up
    ip link set dev vlan1001 up
    exit 0

TASK [Find configuration deployment deploy_script for vlan] ********************
ok: [dut]
ok: [xs]

TASK [Deploy vlan configuration] ***********************************************
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/cumulus_nvue.yml for dut
included: /home/pipi/net101/tools/netsim/ansible/tasks/deploy-config/frr.yml for xs

TASK [set_fact] ****************************************************************
ok: [dut]

TASK [copy the cumulus nvue YAML vlan config file to switch (generated from /home/pipi/net101/tools/netsim/ansible/templates/vlan/cumulus_nvue.j2)] ***
changed: [dut]

TASK [Wait for nvued to start] *************************************************
skipping: [dut]

TASK [set_fact] ****************************************************************
ok: [dut]

TASK [execute on cumulus: 'nv config patch' for vlan config] *******************
changed: [dut]

TASK [execute on cumulus: 'nv config apply -y' for vlan config] ****************
changed: [dut]

TASK [template] ****************************************************************
changed: [xs]

TASK [set_fact] ****************************************************************
ok: [xs]

TASK [run /tmp/config.sh to deploy vlan config from /home/pipi/net101/tools/netsim/ansible/templates/vlan/frr.j2] ***
changed: [xs]

TASK [run vtysh to import vlan config from /home/pipi/net101/tools/netsim/ansible/templates/vlan/frr.j2] ***
skipping: [xs]

PLAY [Deploy custom deployment templates] **************************************
skipping: no hosts matched

PLAY RECAP *********************************************************************
dut                        : ok=40   changed=9    unreachable=0    failed=0    skipped=10   rescued=0    ignored=0   
h1                         : ok=16   changed=4    unreachable=0    failed=0    skipped=8    rescued=0    ignored=0   
h2                         : ok=16   changed=4    unreachable=0    failed=0    skipped=8    rescued=0    ignored=0   
h3                         : ok=16   changed=4    unreachable=0    failed=0    skipped=8    rescued=0    ignored=0   
h4                         : ok=16   changed=4    unreachable=0    failed=0    skipped=8    rescued=0    ignored=0   
xs                         : ok=33   changed=6    unreachable=0    failed=0    skipped=11   rescued=0    ignored=0   



The device under test is a layer-2 switch connected with a LAG VLAN trunk to
another layer-2 switch. Host in the same VLAN should be able to ping each
other.